Basic IP Configuration and Verification

IP addressing is very easy to configure on a Cisco router.  Although the calculation of IP addresses, subnet masks and host can be rather difficult.

The syntax to place an IP address on the interface is:

ip address ip-address mask

Given the routers below, we wish to configure IP addresses on Router1 and Router2.

klo

Remember the the /24 means 255.255.255.0.   For your convenience here is a handy table:

Slash Dotted Decimal Slash Dotted Decimal Slash Dotted 
Decimal
/8 255.0.0.0 /16 255.255.0.0 /24 255.255.255.0
/9 255.128.0.0 /17 255.255.128.0 /25 255.255.255.128
/10 255.192.0.0 /18 255.255.192.0 /26 255.255.255.192
/11 255.224.0.0 /19 255.255.224.0 /27 255.255.255.224
/12 255.240.0.0 /20 255.255.240.0 /28 255.255.255.240
/13 255.248.0.0 /21 255.255.248.0 /29 255.255.255.248
/14 255.252.0.0 /22 255.255.252.0 /30 255.255.255.252
/15 255.254.0.0 /23 255.255.254.0 /31 255.255.255.254

Let's start configuring Router 1

Router>
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int e0
Router(config-if)#ip address 10.1.1.1 255.255.255.0
Router(config-if)#int s0
Router(config-if)#ip address 10.1.2.2 255.255.255.0
Router(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
Router#

We can view the IP addresses on the interface:

Router#sh ip interface brief
Interface IP-Address OK? Method Status Protocol
BRI0      unassigned YES manual admin down down
Ethernet0 10.1.1.1   YES manual admin down down
Ethernet0 10.1.2.2   YES manual admin down down

Router#

We have assigned an IP address to each interface but the interface is still administratively down because we have not executed a 'no shutdown' command on each interface.

Now you should go to each of the interfaces and type no shutdown, this should turn the interfaces to up.

Connect to Router 2 We would also like to add ip addresses to the interfaces.

Router>
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int e0
Router(config-if)#ip address 10.1.
1.2 255.255.255.0
Router(config-if)#int s0
Router(config-if)#ip address 10.1.2.2 255.255.255.0
Router(config-if)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router(config)#exit
 
Router#exit

 

PING

PING, the Packet Inter Net Groper, allows a user to test basic connectivity.  The syntax is:

ping ip-address

The router will send out five echo requests to the destination IP address, if it receives a reply, it will not it with an '!', if not reply is received it will note it with a '.'.

A successful ping:

Router#ping 10.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/37/44 ms 


Router#

A failed ping:

Router#ping 2.2.2.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

Router#

Ping is one of the most commonly used test tools in the word.  PING uses the Internet Control Message Protocol (ICMP) to communicate with other routers.

You can also view your ip addresses using the command show running-config or show ip interface.

 

 

Copyright (c) 2001 Boson Software, Inc.  All Rights Reserved

 

 

 

HOME :: BIMBINGAN TUGAS AKHIR :: ARTIKEL TEKNOLOGI :: ARTIKEL LAINNYA :: LINK PENTING :: BUKU TAMU

Copyright © 2008 Sinau Online email: alifahnuha@gmail.com.